• One 64 bit dual core Intel Itanium processor; either 1.6 GHz/18 MB cache or 1.4 GHz/12 MB cache; or 1.66 GHz/18 MB 9140M processor or 1.42 GHz/12 MB 9120N processor
• One I/O backplane. Either PCI X 2.0 backplane with eight available slots or PCI Express backplane with 8 available slots
• 2 GB PC2 4200 ECC x4 Single rank Registered DDR2 SDRAMs (4×512MB DIMMs)
• Eight DIMM slots (2×4 DIMM slot memory carrier boards)
• One hot swap power supply

• Two dual core 64 bit Intel Itanium processors; either 1.6 GHz/18 MB cache or 1.4 GHz/12 MB cache; or 1.66 GHz/18 MB 9140M processor or 1.42 GHz/12 MB 9120N processor
• One I/O backplane. Either PCI X 2.0 backplane with eight available slots or PCI Express backplane with 8 available slots
• 96 GB PC2 4200 ECC x4 Single rank Registered DDR2 SDRAMs (24×4GB DIMMs)
• 24 DIMM slots (2×12 DIMM slot memory carrier boards)
• Eight Serial Attached SCSI (SAS) disk drive
• Two hot swap power supplies (two supplies enables redundancy)

• Operating System support: HP UX 11i version 2 September 2006 Update; HP UX 11i version 3; Linux RHEL 4 U4 and SLES 10; OpenVMS V8.3 or higher for Integrity servers; and Microsoft Windows Server 2003 Enterprise and Datacenter Edition
• Choice of core storage card.
  For HP UX and OpenVMS based systems: Must select one of two choices: PCI X 8 port Serial Attached SCSI (SAS) host bus adapter or PCI Express 8 port Smart Array (P400) Serial Attached SCSI Controller:
• The PCI X 8 port Serial Attached SCSI (SAS) host bus adapter: Card will be installed in reserved core PCI X I/O slot #1. This card supports up to two internal RAID 1 volumes (2×2 HDDs) and a disk for global hot spare, for a maximum of five disks in RAIDed arrays for HP UX and OpenVMS. All HDDs must be the same size and speed. A second PCI X 8 Internal Port Serial Attached SCSI host bus adapter is supported. In this case each adapter is connected up to a maximum of 4 drives, and the maximum number of disks supported in a RAIDed array is four. The second PCI X 8. Internal Port SAS host bus adapter is not available for standard factory installation; it must be installed via Factory Express or in the field. Use AD348A #006 upgrade product/option to order the second PCI X 8 Internal Port SAS host bus adapter. When a second PCI X 8 Internal Port SAS host bus adapter is installed in an rx3600, it must be located in slot #2, and the LAN adapter moved to slot #10. Please see rx3600 Ordering Guide for factory configuration details
  NOTE: MirrorDisk/UX is available for SW Mirroring on all HDDs in HP UX based systems and HP Volume Shadowing Level 1 for HDDs in OpenVMS based systems.
• PCI Express 8 port Smart Array (P400) Serial Attached SCSI Controller: Requires PCI Express Backplane (AD295A Option 200); card will be installed in public slot #3, leaving 3 available PCI Express slots and 4 available PCI X slots. This card supports internal RAID 1, 5 and 6 configurations. RAID 1 requires a minimum of two identical HDDs, RAID 5 requires a minimum of three identical HDDs, and RAID 6 requires a minimum of four identical HDDs. (Identical disks means same size and speed.) Please see rx3600 Ordering Guide for factory configuration details. NOTE: MirrorDisk/UX is available for SW Mirroring on all HDDs in HP UX based systems and HP Volume Shadowing Level 1 for HDDs in OpenVMS based systems.
  For Windows and Linux based systems: Must select one of three choices: PCI X 8 port Smart Array (P600) Serial Attached SCSI (SAS) controller, or PCI Express 8 port Smart Array (P400) Serial Attached SCSI Controller, or PCI Express 16 port Smart Array (P800) Serial Attached SCSI Controller.
• PCI X 8 port Smart Array (P600) Serial Attached SCSI (SAS) controller: Card will be installed in reserved core PCI X I/O slot #1. Supports internal RAID 1, 5 and 6 configurations.. RAID 1 requires two identical HDDs, RAID 5 requires three identical HDDs, and RAID 6 requires four identical HDDs. Factory set up of RAID 1, 5 and 6 configurations with Smart Array SAS controller is also supported. Please see rx3600 Ordering Guide for details.
• PCI Express 8 port Smart Array (P400) Serial Attached SCSI (SAS) controller. Requires PCI Express Backplane (AD295A Option 200); card will be installed in public slot #3, leaving 3 available PCI Express slots and 4 available PCI X slots. This card supports internal RAID 1, 5 and 6 configurations. RAID 1 requires a minimum of two identical HDDs, RAID 5 requires a minimum of three identical HDDs, and RAID 6 requires a minimum of four identical HDDs. Please see rx3600
  Ordering Guide for factory configuration details.
• PCI Express 16 port Smart Array (P800) Serial Attached SCSI (SAS) controller: Requires PCI Express Backplane (AD295A Option 200); card will be installed in public slot #3, leaving 3 available PCI Express slots and 4 available PCI X slots. This card supports internal and external RAID 1, 5 and 6 configurations.. RAID 1 requires a minimum of two identical HDDs, RAID 5 requires a minimum of three identical HDDs, and RAID 6 requires a minimum of four identical HDDs. Please see rx3600 Ordering Guide for factory configuration details.
• Core PCI X dual port 10/100/1000Base TX LAN (with auto speed sensing; RJ 45 connector, Wake On LAN support)
• Integrated iLO2 Management Processor for remote management and HA monitoring
• Telnet and web console via 10/100Base TX management LAN (RJ 45 connector)
• Two RS 232 serial ports, one for console from the integrated management processor and one from the processor dependent hardware bus (PDH)
• Factory integration of processors, memory, disk drives, removable media, I/O cards, and HP Universal 10000 G2 series racks.
• Rackmountable into 19 inch cabinets-HP Universal 10000 G2 series as well as many third party racks, including field integration into existing HP System E racks
• Optional stand alone pedestal mount, field installation only.
• Three year warranty with next business day on site

• N+1 Hot swap cooling
• One hot swap power supply-optional second power supply for N+1 protection
• Hot Plug PCI X I/O slots
• On line memory page deallocation
• ECC protected DDR2 memory
• Memory double chip spare to overcome single DRAM chip failures
• Dynamic Processor resilience and deallocation
• UPS power management
• Hot Plug internal disks
• Internal RAID support. See Standard Systems Features on previous page and rx3600 Ordering Guide for various levels of RAID support
• Journal file system with HP-UX
• Auto reboot
• HP Serviceguard for HP-UX
• HP Serviceguard Extension for RAC for HP-UX
• HP Serviceguard Extension for SAP for HP-UX
• Serviceguard Manager for HP-UX and Linux Clusters
• HP Event Monitoring Service
• HA Monitors for HP-UX
• HA Toolkits for HP-UX and Linux
• HP Mirrordisk/UX
• Extended Campus Cluster, HP Metrocluster, and HP Continentalclusters for HP-UX
• HP OpenVMS clusters
• HP Volume Shadowing for OpenVMS
• HP RMS Journaling for OpenVMS
• HP System Insight Manager (SIM) for proactive fault management
• Microsoft Cluster Service for Windows Server 2003 Enterprise and Datacenter Edition
• HP StorageWorks Software for HP Integrity Servers running Windows Server 2003 Enterprise Edition. Includes Cluster Extension XP and EVA, Continuous Access, Business Copy and SQL Server Fast Recovery
• HP StorageWorks Cluster Extension XP for Linux

• Separate LAN for system management
• Password protection on console port
• Disablement of remote console ports
• SSL encryption on web console

• HP Ignite UX for installation and deployment of the operating system
• HP Software Distributor UX for software and patch management
• HP Integrity Essentials Foundation Pack for Linux
• HP Integrity Essentials Foundation Pack for Windows including Smart Setup CD for easy server setup and configuration

• Built in Integrity iLO 2 Management Processor for comprehensive remote server management of HP-UX, Linux, Windows and OpenVMS
• HP Servicecontrol suite for HP-UX servers including tools for system administration, asset management, and fault management
• HP-UX kernel configuration for easy, dynamic kernel parameter changes
• HP System Insight Manager (SIM)

• Process Resource Manager for HP-UX resource management
• HP-UX Workload Manager for HP-UX workload management based upon service level objectives
• HP OpenView GlancePlus Pack
• HP Intelligent Networking Pack for Windows
• HP Performance Management Pack for Windows
• Windows System Resource Manager (included with each copy of Windows Server 2003 Enterprise Edition)

• 1.6 GHz with 18 MB Level 3 Cache, 9 MB per core processor
• 1.66 GHz with 18 MB Level 3 Cache, 9 MB per core 9140M processor
• 1.4 GHz with 12 MB Level 3 Cache, 6 MB per core processor
• 1.42 GHz with 12 MB Level 3 Cache, 6 MB per core 9120N processor
   

All processors support:
 

• Level 2 Cache: 1 MB Instruction/256 KB Data per core
• Level 1 Cache: 32 KB
• Four threads (two threads per core)
• Single bit cache error correction
• 50 bit physical addressing
• 64 bit virtual addressing
• 4 GB maximum page size

• Processors can be installed one at a time
• Processors must be installed in the following sequence: 0, 1
• Different speed and cache processors cannot be mixed in the same system

• AD124A-Supports from 2 GB (2×1GB DIMMs) minimum to 32 GB (8×4GB DIMMs) maximum memory; 14.2 GB/s memory bandwidth. The AD124A can be replaced with the AD125A to increase maximum memory beyond 32 GB and to a maximum of 96 GB. Please note, there is no return credit for the AD124A.
• AD125A-Supports from 2 GB (2×1GB DIMMs) minimum to 96 GB (24×4GB DIMMs) maximum; 14.2 GB/s memory bandwidth

1. Memory must be installed in groups of four DIMMs, also known as quads; except for the 2-GB option, which is installed as 2 x 1-GB DIMMs. Note: the 2-GB pair (2 x 1 GB DIMMs), product number AH350A, is only supported with the 8-DIMM carrier (AD124A).
2. Each DIMM in a memory option must consist of equal density DIMMs
3. Memory can be ordered in quads of 4 GB (4×1GB), 8 GB (4×2GB), or 16 GB (4×4GB). There is also a 2-GB pair (2 x 1GB) supported with the 8-DIMM carrier (AD124A).
4. Minimum memory is 2 GB (2×1GB)
5. Maximum memory is 96 GB, using six 16 GB memory quads in memory carrier option AD125
6. Memory must be loaded in the order depicted on the memory carrier board
7. Arrange DIMMs so that the DIMMs with the largest capacity are in the lowest numbered slots.
8. For best performance, all DIMM slots on both memory carrier boards should be populated with the same size DIMM.

The HP Integrity rx3600 can be installed in the field with the Field Rack Kit (AD053A with B01 feature code). This field kit contains the slide mounts, cable management arm, and all other hardware needed to mount an rx3600 into a 19 inch cabinet.

Refer to the 10000 G2 Series Rack Best Practices Guide for information on rack deployment, stabilization and transportation. Go to http://www.hp.com/go/rackandpower for more information.

The rx3600 is also available in a stand alone, pedestal form factor (AD054A). Kit will be shipped in the same box with the system and is field installable only.

HP-UX and OpenVMS based systems with PCI-X 2.0 Backplane:
Must choose the HP PCI X 8 Internal Port Serial Attached SCSI host bus adapter for Core I/O controller (AB036B Option 006 or Option 106). If factory configured RAID is not desired, select Option 006. If factory configured RAID 1 is desired, select Option 106. RAID 1 only is supported on the HP PCI X 8 Internal Port SAS host bus adapter. When selecting Option 106, a minimum of 2 HDDs of the same size and speed are required. A maximum of two internal RAID 1 volumes (2×2 HDDs) and a disk for global hot spare, for a maximum of five disks in RAIDed arrays is supported. A second PCI X 8 Internal Port Serial Attached SCSI host bus adapter is supported. In this case each adapter is connected up to a maximum of 4 drives, and the maximum number of disks supported in a RAIDed array is four. The second PCI X 8. Internal Port SAS host bus adapter is not available for standard factory installation; it must be installed via Factory Express or in the field. Use AD348A #006 upgrade product/option to order the second PCI X 8 Internal Port SAS host bus adapter. When a second PCI X 8 Internal Port SAS host bus adapter is installed in an rx3600, it must be located in slot #2, and the LAN adapter moved to slot #10. Please see rx3600 Ordering Guide for factory configuration details.

Windows and Linux based systems with PCI X 2.0 backplane:
Must choose the HP PCI X 8 port Smart Array (P600) Serial Attached SCSI (SAS) controller for Core I/O controller (AB036B Option 100, or Option 500, or Option 510). Option 100 provides for factory configuration of RAID 1 (requires a minimum of 2 HDDs). Option 500 provides for factory configuration of RAID 5 (requires a minimum of 3 HDDs). Option 510 provides for factory configuration of RAID 6 (requires a minimum of 4 HDDs). All HDDs must be the same size and speed. Please see rx3600 Ordering Guide for details.

Remaining Eight (non-Core I/O) slots:
The two slots (#3 and #4) next to the Core I/O slots have their own dedicated 64 bit 266 MHz PCI X bus and their own independent 2.1 GB/s I/O channel. These slots should be used for high performance PCI X cards, such as clustering interconnects or multi port storage adapters. The next two slots (slots #5 and #6) each have their own dedicated 64 bit 133 MHz PCI X bus and their own independent 1.1 GB/s I/O channel. The independent buses and I/O channels provide improved performance and error containment. Independence protects each I/O card from bus hangs or extended latencies due to the failure or high bandwidth demands of other I/O cards. Independence also ensures that each I/O card can achieve maximum throughput.

The remaining four slots (#7 through #10) share two 64 bit 66 MHz PCI X buses, with two slots allocated to each bus. Each pair of slots shares a 0.5 GB/s I/O channel.

NOTE: Hot-plug operations are not supported with the Linux or OpenVMS operating systems nor in Core I/O slots.

All I/O slots are keyed for I/O cards with 3.3V signaling. Cards that use 5V signaling are not supported in the HP Integrity rx3600.

PCI-Express Backplane:
This backplane also provides ten I/O slots. There are two PCI-X Core I/O slots; one PCI-X Core I/O slot will always have a PCI-X dual port 10/100/1000Base TX LAN adapter (slot #2), and one PCI-X Core I/O slot is provided in the case that the HP PCI-X 8 Internal Port Serial Attached SCSI (SAS) host bus adapter is chosen (slot #1) when ordering an HP-UX or OpenVMS-based system, or if an HP PCI-X Smart Array (P600) 8 Internal Port Serial Attached SCSI (SAS) card is chosen when ordering a Windows or Linux-based system. If a PCI-Express 8-port Smart Array (P400, supports only internal connection to SAS disks) Serial Attached SCSI controller (for HP-UX, OpenVMS, Windows, or Linux) is chosen, or if a PCI-Express 16-port (8 internal ports/8 external ports) Smart Array (P800) Serial Attached SCSI controller (for Windows or Linux, also supports connection to external SAS disks) is chosen, the PCI-X Core I/O slot remains empty and the PCI-Express controller is installed in slot #3.

Each port of a Serial Attached SCSI card can be connected to a Serial Attached SCSI hard disk drive, therefore each HP PCI-X 8 port SAS card supports eight hard disks drives.

HP-UX and OpenVMS based systems with PCI-Express Backplane:
These systems have the two choices for Core I/O controller; the HP PCI-X 8 Internal Port Serial Attached SCSI host bus adapter or the HP PCI-Express 8 Internal Port Smart Array (P400) Serial Attached SCSI controller.

1. HP PCI X 8 Internal Port Serial Attached SCSI host bus adapter (AB036B Option 006 or Option 106). If factory configured RAID is not desired, select Option 006. If factory configured RAID 1 is desired, select Option 106. RAID 1 only is supported on the HP PCI X 8 Internal Port SAS host bus adapter. When selecting Option 106, a minimum of 2 HDDs of the same size and speed are required. A maximum of two internal RAID 1 volumes (2×2 HDDs) and a disk for global hot spare, for a maximum of five disks in RAIDed arrays is supported. Please note that MirrorDisk/UX is available for SW Mirroring on all HDDs in HP UX based systems and HP Volume Shadowing Level 1 for HDDs in OpenVMS based systems.

   A second PCI X 8 Internal Port Serial Attached SCSI host bus adapter is supported. In this case each adapter is connected up to a maximum of 4 drives, and the maximum number of disks supported in a RAIDed array is four. The second PCI X 8 Internal Port SAS host bus adapter is not available for standard factory installation; it must be installed via Factory Express or in the field. Use AD348A #006 upgrade product/option to order the second PCI X 8 Internal Port SAS host bus adapter. When a second PCI X 8 Internal Port SAS host bus adapter is installed in an rx3600, it must be located in slot #2, and the LAN adapter moved to slot #10. Please see rx3600 Ordering Guide for factory configuration details.

   NOTES:
   A. PCI X 8 Internal Port Serial Attached SCSI host bus adapters located in Slot 1 and Slot 2 is the only multiple Serial Attached SCSI Core IO Controller configuration supported on rx3600 servers.
   B. The recommended cabling for this configuration is:
   - SAS 1B cable connected to SAS host bus adapter Slot 1 Port B.
   - SAS 1A cable connected to SAS host bus adapter Slot 2 Port A.
   C. Wake on LAN is not supported on Core IO LAN card when moved to Slot #10.

2. PCI-Express 8-port Smart Array (P400) Serial Attached SCSI Controller (AB036B Option 130, or Option 530, or Option 540). Requires PCI-Express Backplane (AD295A Option Code 200). Option Code 130 provides for factory configuration of RAID-1 (requires a minimum of 2 HDD's). Option Code 530 provides for factory configuration of RAID-5 (requires a minimum of 3 HDD's). Option Code 540 provides for factory configuration of RAID-6 (requires a minimum of 4 HDD's). All HDD's must be the same size and speed. Please see rx3600 Ordering Guide for details. Note: MirrorDisk/UX is available for SW Mirroring on all HDDs in HP-UX based systems and HP Volume Shadowing Level 1 for HDDs in OpenVMS-based systems. A maximum of one 8-port Smart Array (P400) Serial Attached SCSI Core IO Controller is supported on rx3600 servers.

Windows and Linux based systems with PCI-Express Backplane:
These system have three choices for Core I/O controller; the PCI-X 8 Internal Port Smart Array (P600) Serial Attached SCSI controller, or the PCI-Express 8 Internal Port Smart Array (P400) Serial Attached SCSI controller, or the PCI-Express 16-port (8 internal ports/8 external ports) Smart Array (P800) Serial Attached SCSI controller. A maximum of one of these Serial Attached SCSI Core IO Controllers is supported on rx3600 servers.
 

1. HP PCI-X 8 port Smart Array (P600) Serial Attached SCSI controller (AB036B Option Code 100, or Option Code 500, or Option Code 510). Option Code 100 provides for factory configuration of RAID-1 (requires a minimum of 2 HDD's). Option Code 500 provides for factory configuration of RAID-5 (requires a minimum of 3 HDD's). Option Code 510 provides for factory configuration of RAID-6 (requires a minimum of 4 HDD's). All HDDs must be the same size and speed. Please see rx3600 Ordering Guide for details.
    
2. PCI-Express 8-port Smart Array (P400) Serial Attached SCSI Controller (AB036B Option 130, or Option 530, or Option 540). Requires PCI-Express Backplane (AD295A Option 200). Option 130 provides for factory configuration of RAID-1 (requires a minimum of 2 HDDs). Option 530 provides for factory configuration of RAID-5 (requires a minimum of 3 HDDs). Option 540 provides for factory configuration of RAID-6 (requires a minimum of 4 HDDs). All HDDs must be the same size and speed. Please see rx3600 Ordering Guide for details.
   NOTE: The P400 controller supports a mixture of RAID-1 on two like drives and RAID-5 on five like drives, and combining RAID-1 and RAID-5 is supported, but not as factory integration.
   
    
3. PCI-Express 16-port (8 internal ports/8 external ports) Smart Array (P800) Serial Attached SCSI Controller (AB036B Option 150, or Option 550, or Option 560). Requires PCI-Express Backplane (AD296A Option 200). Option 150 provides for factory configuration of RAID-1 (requires a minimum of 2 HDDs). Option 550 provides for factory configuration of RAID-5 (requires a minimum of 3 HDDs). Option 560 provides for factory configuration of RAID-6 (requires a minimum of 4 HDDs). All HDDs must be the same size and speed. Please see rx3600 Ordering Guide for details.

Remaining Eight (non-Core I/O) slots:
The two slots (#3 and #4) next to the Core I/O slots share a PCI-Express x8 1.3-GB/s I/O channel. The next two slots (slots #5 and #6) each have their own PCI-Express x8 2.6-GB/s I/O channel. The independent I/O channels provide improved performance and error containment. Independence protects each I/O card from bus hangs or extended latencies due to the failure or high bandwidth demands of other I/O cards. Independence also ensures that each I/O card can achieve maximum throughput. These slots should be used for high performance PCI X cards, such as clustering interconnects or multi port storage adapters.

The remaining four slots (#7 through #10) are PCI-X slots. Slots #7 and #8 each have their own dedicated 64 bit 133 MHz PCI X slot; slot #7 is 1.1 GB/s and #8 is .5 GB/s. Slots #9 and #10 share a 64-bit 66-MHz PCI-X 0.5 GB/s I/O channel.

NOTE: Hot plug operations are not supported with the Linux or OpenVMS operating systems or for the PCI X Core I/O slots for any operating system. Hot plug operations are not supported for any operating system in slots #3 or #4.

All I/O slots are keyed for I/O cards with 3.3V signaling. Cards that use 5V signaling are not supported in the HP Integrity rx3600.

Card cannot be in a shared slot with an AB551A graphics card. Requires full length slot.

J3525A